Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Blog Article
Everybody may have their personal way of thinking with regards to How to Install a Bathtub.
Mounting a bathtub isn't specifically rocket science, yet it does need solid plumbing, woodworking, as well as sometimes, tiling abilities. Replacing an old bath tub with a new one is also a moderately difficult job. If the old bathtub is easily obtainable, the project can relocate quickly; if you need to open up a wall to get rid of the old tub as well as place the new bath tub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need an assistant to move out the old bathtub and set in the brand-new one. Make sure you have certified on your own for the job as well as fit attempting it. Instead of working with a contractor to take over a halfway-completed task, it is better to think about using one before you begin. Opportunities are you might need an expert plumber to make tube links.
This write-up will assist you mount a brand-new bathtub in your bathroom if you have currently gotten a brand-new tub and do not require to change the arrangement of your previous supply of water pipelines.
Your devices and also product checklist ought to make up the following:
Planning for the Installment
To start with, the sustaining structure supplied with the bath ought to be fitted (if needed) according to the producer's instructions. Next, fit the taps or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet includes a plastic washer, it is fitted between the bathroom as well as the faucets. On a plastic bath, it is also sensible to fit a supporting plate under the faucets system to avoid stress on the tub.
Fit the flexible tap adapters to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which should be fitted inside the bath. Make sure you utilize all of the provided washing machines.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom should now be ready to be fitted in its last setting.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your installation, after that the first thing you should do is separate the water supply. After doing so, activate the taps to drain pipes any water staying in the system. The process of eliminating the existing faucets can be rather troublesome as a result of the limited gain access to that is often the case.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a fabric prepared for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been removed, utilize the same tool to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old securing compound.
Before going on to fit the new faucets, contrast the pipe links on the old taps to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Mounting the Bath tub
Utilizing the two wood boards under its feet, position the tub in the required position. The wooden boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto 4 little points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and also changing the feet on the tub until the spirit level reviews degree.
To set up taps, fit all-time low of the furthest adaptable faucet port to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other tap.
Switch on the water as well as inspect all joints and also brand-new pipework for leaks and tighten them if essential. Load the bath tub and also check the overflow electrical outlet as well as the normal outlet for leakages.
Ultimately, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bath tub must wait up until the bathtub has actually been made use of a minimum of once as this will certainly resolve it into its last placement.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will certainly need a plastic port to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end provides a connection to the current supply pipes.
If you need to fit a monobloc, then you will certainly need reducing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next, place the tap in the mounting opening in the bath/basin making certain that the washing machines remain in location between the faucet as well as the sink. Protect the tap in position with the maker offered backnut. As soon as the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by using corrugated copper piping or with regular faucet connectors. The previous kind should be attached to the faucet finishes initially, tightening just by hand. The supply pipes can later on be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to split a rigid seal, creating the water to penetrate the wall surface between the bathroom and the tiling, bring about problems with wetness and feasible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to blend in your fixtures and also fittings. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can load it with twists of drenched newspaper or soft rope. Remember to always fill the bath tub with water prior to securing, to allow for the motion experienced when the tub is in use. The sealant can fracture fairly very early if you do not take into account this motion prior to sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are likewise conveniently readily available on the market. It is a good idea to fit the floor tiles using water-resistant or water resistant glue and also cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As an avid reader on Tools You Need to Install a New Bathtub , I think sharing that excerpt was essential. Are you aware of anybody else who is very much interested in the subject? Why not promote it. I thank you for reading our article about How to Install a Bathtub Yourself.
Request Estimate
Report this page